<label id="hi3ik"><kbd id="hi3ik"></kbd></label>
    <center id="hi3ik"></center>
    <span id="hi3ik"><noframes id="hi3ik">
    歡迎來到中科聚峰機械有限公司!

    24小時服務熱線:

    400-879-1999

    點擊撥打服務熱線:400-879-1999
    當前位置:首頁>新聞中心>常見問題>如何解決自動上料攪拌車出現的故障問題

    如何解決自動上料攪拌車出現的故障問題

    來源:http://www.djkenshu.com/ 日期:2022-11-07 發布人:guanli
    概述:經常使用自動上料機攪拌車,時間久了難免會出現故障,出現故障不要怕,小編來告訴你如何解決故障問題。 If you often use the mixer
    經常使用自動上料機攪拌車,時間久了難免會出現故障,出現故障不要怕,小編來告訴你如何解決故障問題。
    If you often use the mixer truck of the automatic feeder, it is inevitable that a failure will occur after a long time. Don't be afraid of the failure. I will tell you how to solve the problem.
    1.自動上料攪拌車工作時有噪音檢查濾芯清洗或更換檢查吸油管路有無漏氣擰緊或更換密封檢查油的標號更換合適標號液壓油檢查泵、馬達、萬向軸等連接螺栓緊固連接螺栓油箱油位低補油。
    1. When the automatic feeding mixer is working, there is noise. Check whether the filter element is cleaned or replaced. Check whether there is air leakage in the oil suction pipe. Tighten it or replace the seal. Check whether the oil label is correct. Replace the hydraulic oil with the appropriate label. Check whether the connecting bolts of the pump, motor, universal shaft, etc. are fastened. Connect the connecting bolts. The oil tank is filled with oil when the oil level is low.
    2.攪拌罐起動慢檢查濾芯清洗或更換檢查吸油管路擰緊或更換密封檢查油箱油位補油檢查控制軟軸連接或更換軟軸。
    2. Start the mixing tank slowly. Check whether the filter element is cleaned or replaced. Check whether the oil suction pipe is tightened or the seal is replaced. Check the oil level in the oil tank. Make up oil. Check whether the control flexible shaft is connected or replace the flexible shaft.
    自動上料攪拌車
    3.油溫過高液壓油標號不對(標號混用)更換合適標號液壓油液壓油臟更換液壓油超負荷工作調整負荷冷卻風扇不轉,溫控器損壞更換溫控器泵吸空補油冷卻器過油量不夠補油液壓件內泄嚴重更換有關零件檢查濾油器(吸油)清洗或更換濾油器。
    3. The oil temperature is too high. The hydraulic oil grade is incorrect (mixed grade). Replace the hydraulic oil with the proper grade. The hydraulic oil is dirty. Replace the hydraulic oil. The hydraulic oil is overloaded. Adjust the load. The cooling fan does not turn. The temperature controller is damaged. Replace the temperature controller. The pump suction and makeup oil coolers. The oil flow is insufficient. The hydraulic parts have serious internal leakage. Replace the relevant parts. Check the oil filter (oil suction). Clean or replace the oil filter.
    4.攪拌罐不能轉動無補油壓力檢查補油泵及油箱補油壓力過低。檢查油箱油位是否滿足液壓系統工作補充同品牌同型號油液連接盤花鍵套內花鍵損壞更換連接盤或主泵通軸檢查吸油管路是否斷裂、被擠壓更換或修理吸油管路排量控制拉線是否脫開連接好排量控制拉線檢查伺服閥、安全銷更換安全銷控制油路被異物堵塞清晰油路濾油器太臟,清洗或更換濾油器。
    4. The mixing tank cannot rotate without oil make-up pressure. Check that the oil make-up pressure of the oil make-up pump and oil tank is too low. Check whether the oil level in the oil tank meets the requirements of the hydraulic system. Replenish the oil of the same brand and model. Replace the spline inside the spline sleeve. Replace the connecting disc or the main pump shaft. Check whether the oil suction pipeline is broken, squeezed. Replace or repair the oil suction pipeline. Check whether the displacement control cable is disconnected. Check whether the servo valve and safety pin are connected. Replace the safety pin. Control the oil circuit is blocked by foreign matters. Clear the oil circuit. The oil filter is too dirty. Clean or replace the oil filter.
    如何解決自動上料攪拌車出現的故障問題?以上就是問題的解答了,希望能夠給您幫助,當然你要記住日常中好好維護設備。關注我們http://www.djkenshu.com,了解更多使用事項!
    How to solve the failure problem of automatic feeding mixer? The above is the answer to the question. I hope it can help you. Of course, you should remember to maintain the equipment well in daily life. Follow us http://www.djkenshu.com , learn more!

    截屏,微信識別二維碼

    国产精品成熟老妇女|KAGNEY与黑人激烈|强迫屈辱玩弄粗暴H|春药高潮抽搐流白浆在线观看|我怕来不及电视剧|国产成人精品午夜福利|染头发|赵丽蓉小品全集|女人张腿让男桶免费视频|国产亚洲精品久久久久9999